E-Shop

Ador Champmig 600

Ask For Price

Champmig 600

 

The world class Inverter based MIG Welder

 

 

INTRODUCTION

CHAMP MIG 600 is an IGBT inverter based welding power source, suitable for GMAW applications. The IGBT Power module, high frequency transformer and fast recovery diode are used as key device for power conversion and transmission to assure better efficiency and performance.

The complete system consists of power source, wire feeder, water cooled or gas cooled torch, water cooling unit (for water cooled systems) and interconnecting cables.

 

 

DETAILS OF COMPLETE SYSTEM

 

Sr. No.

Description

CHAMPMIG 600 A

CHAMPMIG 600 E

1Power Source

ICVR 600

ICVR 600

2Wire feeder

FEEDLITE 40 (NEH-RC)

FEEDLITE 40 (NEH-RC)

3Torch

ADOR-MTG 600 E.

ADOR TW 502 (E)

 

 

SALIENT FEATURES

 

  • Inverter based digitally controlled GMAW outfit
  • Auto “Weld Stop” when welding torch is taken away from weld job
  • Digital Panel for adjusting the welding
  • 25% more Energy efficient than conventional machines.
  • Maximum Power factor is 0.95
  • Excellent dynamic response enables superior arc characteristics. 2T, 4T operating modes
  • Dynamic Inductance adjustment for better arc control
  • Crater voltage and Crater current adjustment through digital panel. Unique feature of Pinch off pulse to avoid globule formation.
  • Automatic “Weld Stop” facility.
  • Normal/ Creep feeding selection available on on front panel.

 

 

PROTECTION

The equipment is provided with following protections.

  1. a) Under Voltage and Over Voltage: If supply voltage goes lower or higher than set limit, error message is displayed on Display
  2. b) Over Temperature: If the temperature of the main power elements is more than safety limits, error message is displayed
  3. c) Single Phasing Protection: If any one of the three phases (R, Y, and B) is absent, welding will stop. Welding current would not be available in this condition

 

 

SPECIFICATIONS

 

Technical  Specifications

Unit

ICVR 600

Input  
Input Supply :  
Voltage 

Volt

415, +15%, -10%

Phase

No

3 Ø

Frequency

Hz

50/ 60

Max Input KVA    
@ 100% duty cycle

KVA

21.5

@ No Load

KVA

0.31

Output  
Open Circuit Voltage

Volts +/-5%

65

Welding Current Range  

Amp

65-600

Welding Current (40°C 10 minutes  cycle)  
@ 60% duty cycle  

Amp

600

@ 100% duty cycle

Amp

465

Welding Voltage Range

Volt

16-45

Crater Current Range

Amp

65-600

Crater Voltage Range

Volt

16-45

Mode of operation

2 track, 4 track, Gas check,  OCV

check facility

Remote Control

For setting voltage & current

Power Factor 

Max 0.94

Efficiency

%

89% @ 100% duty cycle

General  
Compatibility to International  standard 

As per Std. EN60974-1

Wire feed speed

m/min

1.5-18

Suitable Welding Wire Diameter

mm

Aluminum 1.2 – 1.6

Steel 0.8,1.0,1.2 & 1.6

Ingress Protection

Class

IP23

Cooling  

Type

Forced Air

Dimensions (Approx.)    
Length

mm

670

Width

mm

450

Height

mm

620

Weight  

Kg

56

Audio Noise Emission

dB

70

Technical  Specifications

Unit

Feedlite 40 (NEHR)C

Suitable for wire Ø

mm

0.8,1,1.2,1.6 mm

Wirefeed speed

mtr/min

1.5 to 18 mtr/min

Wire roll drive

Four

Wire drive motor

Type

Permanent Magnet DC

Wire feeder Motor voltage

V

42

Wire feeder fitted with rollers

1.2/1.6 for sold wire 2 no

Suitable for Wire Spool  capacity

Kg

15

Dimensions  

Length

mm

563

Width

mm

230

Height

mm

410

Weight (without spool)

Kg

16 (Approx)

 

 

  • Warranty : One year from the date of commissioning. ADOR WELDING LIMITED warrants that all new equipment sold from Plant/Area Offices / Authorised Distributors are free from defects in materials and workmanship and will perform in full accordance with applicable specifications.
  • In view of continuous development, ADOR WELDING LIMITED reserves the right to modify/change the design and /or the specifications without any prior notice.
  • Backed by dedicated customer care package.

 

 

 

Brands

ADOR

SKU: Champmig 600 Categories: , , Tags: ,
×